To attach a mantel to a brick fireplace, set masonry anchors or epoxy-set rod into solid brick, mount a bracket or ledger to them, and shim for level. Keep every hole out of the firebox, smoke chamber and flue. Check the clearance rules before you choose the height.
Check the brick first
Brick is not all the same. Before you choose a method, check what you have:
- Solid brick: a structural wall that holds the heaviest anchors.
- Hollow-core brick: brick with open cores. It needs a different anchor, as described below.
- Veneer: a thin layer of brick or stone over a wall. It does not carry the same load as structural brick.
Tap the surface and look at the edges. If you are not sure, a mason can tell you what you have. Do not hang a heavy mantel from veneer alone.
Choose a mounting method
- Hidden steel rod bracket: rods are set into the brick and the beam slides over them.
- Ledger board with a box mantel: a board is fixed to the brick, and a hollow mantel slides over it.
- Corbels: brackets under the mantel that carry the weight down to the wall.
- French cleat: two interlocking pieces, one on the brick and one on the back of the mantel.
Each method needs anchors into solid masonry. The choice depends on the look you want and how heavy the mantel is.
Choose the right anchor for your brick
- Sleeve anchors: good for solid brick. Drill a hole the same diameter as the anchor, such as 3/8 or 1/2 inch.
- Epoxy-set threaded rod: best for old, soft or hollow-core brick. In hollow units, use a screen tube so the epoxy holds.
- Wedge anchors: designed for solid concrete. In brick they can crack the unit, so avoid them.
- Tapcon screws: for light loads only. A 3/16 inch Tapcon uses a 5/32 inch bit; a 1/4 inch Tapcon uses a 3/16 inch bit. Embedment is 1 to 1-3/4 inches.
Construction adhesive alone will not hold a heavy mantel on brick. Use it as an extra, not as the main fastener.
Where to drill: brick face, joints and the firebox
Drill into the brick face where you can. Brick usually holds heavier loads than mortar. Mortar joints are easier to patch if you make a mistake, but sources differ on which is stronger, so use judgment for your wall.
Keep anchors several inches from brick edges and corners. Drilling close to an edge can spall the brick.
Never drill into the firebox, smoke chamber or flue. Those spaces hold heat and smoke, and a hole there can let heat reach the framing or cause a fire.
Drilling steps
- Mark the centers of the holes on a 2x4 template, level it against the brick, and mark through the template.
- Use a hammer drill with a carbide masonry bit.
- Mark the drill depth on the bit with tape.
- Clear the dust from each hole before you insert the anchor.
- Set the anchor to the depth specified by the manufacturer.
Wear eye protection and a dust mask. Brick dust contains crystalline silica.
Shim and level before you tighten
Brick is rarely flat, so the anchors may not line up with a straight beam. Shim behind the ledger or bracket to level it, or scribe the back of the mantel to fit the wall. Check the level and plumb before the final tightening.
Do not overtighten sleeve anchors. Overtightening can crack old brick.
How many anchors does a heavy mantel need?
Use at least two anchors per bracket or ledger. For a beam heavier than about 50 pounds, use more. Spread the anchors across the length of the mantel so the load is not carried by one point.
Clearances and height above the opening
The mantel must meet the code clearances:
- At least 6 inches from the opening, for combustible material.
- Within 12 inches of the opening, combustible projection no more than 1/8 inch for every inch of distance.
- Projections more than 1-1/2 inches out generally need 12 inches above the top of the opening.
One common guide suggests keeping the mantel at least 15 inches above the firebox. That is more conservative than the 12-inch code rule, so it is a reasonable target, but it is not a code minimum. The appliance manual and local code can require more. Follow the strictest of the three.
For the full clearance rules, see the fireplace mantel code guide.
Common mistakes
- Wedge anchors in brick. They can split the unit.
- Relying on adhesive alone. Adhesive is not a structural fastener for a heavy mantel.
- Treating veneer as structural brick. A thin veneer does not carry the same load.
- Skipping the shim. An uneven wall makes a crooked mantel.
Safety: dust and drilling
Brick dust contains crystalline silica. Wear eye protection and a dust mask. Keep the drill away from the firebox and flue, and work with a second person when lifting a heavy beam.
For the general steps that come after the anchors are set, see how to install a floating mantel. For the parts of the firebox and flue, see the parts of a fireplace. For hardware and install costs, see how much a fireplace mantel costs.