A gas log fireplace burns gas through a burner placed under ceramic or refractory logs inside an existing fireplace. A gas insert is a sealed unit that fits into the firebox and vents through a liner. Vented logs need an open chimney. Vent-free logs need no chimney, but they release their combustion products into the room. Electronic ignition models need power, so they may not work in an outage.
How a Gas Log Set Works
A gas log set has three main parts:
- A burner pan. Gas flows into a metal pan under the logs.
- A valve. The valve controls the gas and, on most units, includes a safety shutoff.
- The logs. These are usually ceramic fiber or refractory cement, shaped to look like wood.
The gas flows through small ports in the burner and is lit by a standing pilot or an electronic spark. When the gas burns, the logs glow and give off radiant heat. Natural gas or propane can be used, and the two fuels need different burner settings.
Safety valves shut off the gas if the pilot goes out. On a standing-pilot unit, a thermocouple or thermopile senses the pilot’s heat and holds the valve open. If the pilot goes out, the valve closes.
Vented and Vent-Free Logs
Vented (decorative) logs sit in a traditional wood-burning fireplace with a chimney. They give tall, yellow flames that look like a wood fire. The damper must be fixed open or removed while the logs run, so the exhaust can exit through the chimney. Vented logs are mainly for the look of the fire. They can lose more heat up the chimney than they put into the room.
Vent-free logs burn cleanly enough that the products of combustion stay in the room, without a chimney. They have an oxygen depletion sensor (ODS) that shuts the gas off if the oxygen in the room drops to about 18 percent. Normal air is about 20.9 percent. Vent-free burners add water vapor to the room, about 1 gallon for every 100,000 BTU of natural gas burned.
Vent-free units are restricted or banned in some places, including California, and in some cities, states and provinces. Some rooms also have limits on input. Check local code before you consider one.
How Gas Inserts Differ
A gas insert is a sealed firebox that fits into an existing fireplace. It has a glass front. Combustion air comes from outdoors through one pipe, and exhaust goes out through another. These can be two liners or a coaxial liner that runs up the chimney. Direct-vent inserts are commonly around 70 to 85 percent efficient or more, which is much higher than vented logs.
Because the firebox is sealed, an insert doesn’t draw room air. An insert also needs the glass, gasket and vent to be intact. If any of these fail, combustion products can leak into the room.
Ignition Types and Power Outages
There are two main ignition types:
- Standing pilot (millivolt). A small pilot stays lit, and a thermopile makes the small current the valve needs. These units don’t need house electricity to run. In a power outage, the burner keeps working. Only the blower stops, and heat output can drop.
- Electronic (intermittent pilot ignition, or IPI). A spark lights the pilot each time you turn the unit on. These need 120-volt power or battery backup. Without either, they won’t light in an outage.
Some older log sets have a manual key valve and are match-lit. These can be used without power, but they need a careful hand-lighting process.
Check your model’s ignition type before you plan around an outage. Our guide on whether you can flush during a power outage covers outage planning for the rest of the home.
Gas Logs or an Insert: Which Fits?
- Gas logs suit an existing wood fireplace where you want the look of a fire with little work. Vented logs need an open chimney, and their heating is modest.
- A gas insert suits a homeowner who wants more heat from an existing fireplace. Inserts need a venting kit and usually a professional install.
- A new gas fireplace is the choice when there is no existing fireplace. Read building a gas fireplace for the venting and gas line options.
Input sizes differ. Vented log sets are often around 30,000 to 90,000 BTU per hour, and inserts are often 20,000 to 40,000 BTU per hour, depending on the model.
Common Misconceptions
- Vented logs heat the room efficiently. They can lose more heat up the chimney than they give off.
- Every gas fireplace works in an outage. Electronic ignition units without battery backup won’t light.
- Vent-free means zero emissions. Combustion products and moisture go into the room.
- Gas fireplaces need no chimney or vent inspection. Vents, terminations and liners still need checking.
- You can burn wood on or around gas logs. Don’t add wood, pinecones or other materials to a gas set.
Safety Basics
- Install a carbon monoxide alarm near any gas fireplace, especially a vent-free one. See our guide to carbon monoxide risk and detectors.
- Never close the damper on vented logs while the burner is lit.
- If you smell rotten eggs, don’t light or switch anything. Leave the home and call the gas utility or 911 from outside.
- Have the unit serviced every year. The service schedule explains what the visit covers.
- For flame and soot problems, see gas fireplace flame problems.