A wood burning stove heats a room far more efficiently than an open fireplace. An EPA-certified stove is typically 65 to 80% efficient, while an open masonry fireplace is about 10% efficient or less, and it can pull warm room air up the chimney. That gap is the main reason stoves are the usual choice for heating, while fireplaces are mostly valued for the look and sound of an open fire.
How each one heats your home
A wood stove is a closed firebox with a door. Its steel or cast iron body heats up and radiates warmth from all its surfaces, and air warmed against it rises into the room. An open fireplace sends most of its heat out the front by radiation, and a large share of the warm air in the room can be drawn up the flue.
Glass doors on a fireplace cut warm-air loss once the fire dies down, but they add little heat. They also don’t control combustion air, so they don’t turn a fireplace into a stove.
Efficiency and heat output
Efficiency is the share of the fuel’s energy that ends up as usable heat. US stove ratings use the higher heating value (HHV) basis. The EPA publishes efficiency, emissions and heat output for each certified model in its Certified Wood Heater Database. For model-level numbers, see our guide to which wood stove brand is the most efficient.
Open fireplaces are not covered by the EPA’s stove emissions limits, and most of their heat leaves through the chimney. Inserts, which are EPA-certified stoves built to fit an existing masonry fireplace, are about as efficient as freestanding stoves. Masonry heaters store heat in dense masonry and release it slowly. They can reach about 80% or more, but they are large built-in systems rather than a simple swap.
Burn time and reloading
A non-catalytic stove typically burns for about 5 to 10 hours on a load of wood. A catalytic stove can run for 12 to 30 hours or more on its lowest setting, depending on the model. An open fireplace usually needs fresh wood every 30 to 60 minutes.
Burn times depend on the wood, the draft and how far you turn the controls down, so treat these as typical ranges rather than guarantees. Our guide to catalytic and non-catalytic stoves explains the difference in more detail.
Upfront cost and installation
Installed cost varies widely with your house, chimney and region. In the US, a freestanding stove with a new chimney typically costs about $3,000 to $8,000 or more. An insert with a liner typically costs about $3,000 to $6,000 or more. Building a new masonry fireplace is usually more expensive than either option, and it heats less.
Inserts need a stainless steel liner from the insert collar to the top of the chimney. Most manufacturers require it, and local code varies. Ask for written quotes that include the chimney work, floor protection and a final inspection, because those items can add up quickly.
Inserts: a stove inside your existing fireplace
If you already have a masonry fireplace, an insert can bring stove efficiency to the same opening without rebuilding the hearth. Before buying one, have the chimney swept and inspected. Check the insert’s clearance and liner requirements, and make sure its firebox size fits the opening. For small units and compact stoves, see our guide to small wood burning stoves.
Safety and clearances
Both appliances need proper clearances and ember protection. A stove must keep the distances on its listing label from combustible materials. An unlisted stove generally needs 36 inches under NFPA 211. See our guide to what sits behind a wood stove for how heat shields change those figures. A fireplace is open to the room, so it needs a spark screen and carries a higher risk of sparks and creosote buildup.
The chimney should follow the 3-2-10 rule: extend 3 feet above the roof penetration and at least 2 feet higher than anything within 10 feet. NFPA 211 recommends a yearly inspection. CSIA guidance is to clean the flue when soot reaches about 1/8 inch. Install carbon monoxide alarms on every level and near sleeping areas.
Common misconceptions
- “A roaring fireplace heats the house.” Rooms away from the fire often get colder, because the fireplace pulls warm room air up the chimney.
- “Glass doors turn a fireplace into a stove.” Glass doors don’t control combustion air.
- “Higher BTU is better.” An oversized stove is run smoldering, which builds creosote. See our guide to sizing a wood stove.
Which should you choose?
- Choose a wood stove if the main goal is heat, efficiency and control over the fire.
- Choose an insert if you already have a masonry fireplace and want stove performance in the same opening.
- Choose an open fireplace if you mainly want the look of a live fire and accept that it provides little heat.
If you are looking at imported models, see our European wood stoves guide before you compare prices.