Building a Fireplace

How Much Does It Cost to Build a Fireplace?

Rough installed costs to build a fireplace by type, from electric to masonry, plus the costs people miss and how to compare quotes. Prices vary by region.

On this page
  1. Typical installed costs by type
  2. What drives the price
  3. Costs people often miss
  4. Running costs
  5. How to compare quotes
  6. Do not cut corners on the chimney and footing

Installed costs range from a few hundred dollars for a plug-in electric unit to tens of thousands of dollars for a new masonry fireplace with a full chimney. The figures below are approximate US ranges. They vary by region, scope, and materials, so treat them as a starting point and get local quotes.

Typical installed costs by type

Type Rough installed cost
Electric fireplace About $200 to $3,000. Built-in framed units cost more.
Direct-vent gas fireplace About $3,000 to $8,000 or more, not counting a separate gas line
Gas or wood insert in an existing fireplace About $3,000 to $7,000, including a liner
Factory-built wood fireplace, with chimney and chase About $3,000 to $10,000
High-efficiency (EPA-certified) wood fireplace About $5,000 to $15,000
Wood stove with a new chimney About $3,000 to $7,000
New masonry fireplace and chimney About $10,000 to $30,000 or more
Masonry heater About $15,000 to $40,000 or more
Outdoor fireplace About $3,000 to $20,000 or more

Online estimates differ, and some run higher for installed wood and gas units. Use these figures to set expectations, then compare written quotes for the same scope of work.

What drives the price

  • Chimney height and type. A new or relined chimney is often one of the largest costs for a wood or gas fireplace.
  • Footings and structure. A masonry fireplace needs a footing. Changes to framing or floors add cost.
  • Roof penetration. Cutting and flashing a roof adds labor.
  • Finish materials. Stone, tile, and custom millwork can add significantly to the total.
  • Labor rates. Contractor rates vary by region.

Costs people often miss

  • Chimney liner. A stainless steel liner, installed, often costs about $2,000 to $5,000.
  • Permits. Permit fees commonly run about $100 to $500 or more.
  • Mantel and surround. These often run about $500 to $5,000 or more. Stone and custom millwork cost the most.
  • Gas line and electrical work. A new gas line is an extra cost, often priced by the foot. Adding or upgrading electrical circuits adds labor and materials.
  • Chimney inspection. If you reuse an existing chimney, budget for a Level 2 inspection first.

Running costs

Wood costs depend on local cord prices, and those vary a lot by area. Gas and electric costs depend on local utility rates. Wood-burning fireplaces need regular chimney cleaning, and gas fireplaces need an annual service check. Budget for both.

How to compare quotes

  • Ask for the same scope from each contractor. Include the unit, venting, chimney, permit, finish work, and any gas or electrical connections.
  • Ask whether the permit and inspections are included.
  • Check the chimney height and liner type. A low price may leave out the chimney.
  • Confirm the unit’s listing or model number so each quote is for the same product.
  • Get at least two or three written quotes before you choose.

Do not cut corners on the chimney and footing

Doing a masonry build yourself to save money rarely saves as much as expected. Materials make up a large share of the cost, and code inspections still apply. The footing, firebox, and chimney are where mistakes cause fires and carbon monoxide problems, so this is the work to leave to a licensed professional.

For the bigger decision between a factory unit and masonry, see prefab vs site-built fireplaces. For the venting options that set the price, see can you put a fireplace into a house?

The complete guide to building a fireplace

Wood Burning Fireplace Construction: How Fireplaces Are Built
Read the guide

Keep exploring

Guides from other topics

All topics →