Quick answer
Most masonry fireplaces can be converted to burn wood efficiently. You install a wood-burning insert or a freestanding stove, and run a stainless steel liner up the existing chimney. Whether it’s suitable depends on the chimney, the firebox and the room. Every conversion needs a chimney inspection, a permit and a correctly sized liner. An insert installed typically costs roughly $3,500 to $7,000 or more, and the liner alone often adds $1,000 to $3,000.
Why convert an open fireplace?
An open masonry fireplace is very inefficient. It’s about 10% efficient or less, and it can be a net loss, because it draws warm room air up the flue. An EPA-certified stove or insert commonly reaches about 70% to 80% or more. The conversion gives you a closed firebox, a controlled burn, and far more of the wood’s heat in the room.
Your three conversion routes
- A wood-burning insert. The insert sits inside the existing firebox and vents through a liner in the chimney. This suits a sound masonry firebox and chimney, and it keeps the look of the opening. For the types on offer, see fireplace inserts: types and models.
- A hearth-mounted freestanding stove. The stove sits on the hearth and connects through the damper area. It needs a sealed connection and the right clearances.
- A freestanding stove in front of the fireplace. The stove stands in front of the opening, and a connector pipe runs into the fireplace. It needs clearance from combustibles and a proper hearth.
If your fireplace is factory-built (metal) rather than masonry, the options narrow. Factory-built fireplaces generally need an insert listed for that specific unit, with the maker’s approval. For that case, see fireplace insert vs zero clearance fireplace.
The steps, in order
Whichever route you choose, the work follows this order: inspect, sweep and repair, choose the right appliance, get the permit, install the liner and cap, set the appliance, block off the opening, and finish with a final inspection.
Step 1: Inspect the chimney first
Start with a certified chimney sweep who will carry out a Level 2 inspection. NFPA 211 requires this when you change the appliance or the fuel type. It often includes a video scan of the flue, which can find cracks and gaps that a visual check misses.
Don’t assume a chimney is fine because it looks fine. Cracked tiles and missing mortar joints are often found only by camera.
Step 2: Sweep and repair
Clean out the creosote, and repair any damaged masonry before the new appliance goes in. Old creosote can ignite once a stove’s hotter exhaust gases reach it, so the flue has to be clean first.
Step 3: Choose an appliance sized for the space
Size the stove or insert to the room, not to the biggest unit you can fit. An oversized stove gets run in a smoldering state, which builds creosote in the flue. Compare each model’s heat output against the room’s size and insulation, and check the manual’s sizing guidance.
For an insert, measure the opening carefully before you order. How to measure your fireplace for an insert walks through each measurement.
Step 4: Get the permit
Most US jurisdictions require a building or mechanical permit for a new wood stove or insert. The permit triggers an inspection of clearances, hearth protection, the liner, and the appliance’s listing. Insurers may also ask for proof of a permitted, inspected install. Do you need a permit to install a fireplace insert or wood stove? covers the details.
Step 5: Install the liner and cap
The liner is usually stainless steel. For wood, use 316Ti or 316L, listed to UL 1777. It runs the full length from the appliance to the top of the chimney.
- Minimum and standard. NFPA 211 sets a minimum of a “positive connection” to the first flue tile. Most insert listings, common practice and Canada’s CSA B365 call for a full-length liner.
- Diameter. The liner usually matches the appliance’s flue collar, which is commonly 6 inches. Don’t reduce the diameter unless the manual allows it.
- Insulation. Insulating the liner, with a blanket wrap or a pour-in mix, improves draft. Some installs need it to meet clearance requirements.
- Damper. The old damper is often removed or fixed open so the liner can pass through.
- Cap. A cap at the top of the chimney keeps out rain, debris and animals.
For more on whether an insert needs a liner, see do you need a chimney liner for a fireplace insert.
Step 6: Set the appliance and block off the opening
Install a block-off plate: a sheet-metal plate sealed around the liner at the damper area. It keeps heat from escaping into the chimney, and it stops cold air from dropping into the room.
Set the appliance according to its label and manual. Clearances to combustible materials and the hearth extension are set by the listing. Ember protection is typically 16 to 18 inches in front of the appliance and about 8 inches at the sides, but this varies by listing and country.
Step 7: Surround, curing and final inspection
Fit the surround or face panel and seal any gaps. Many manuals call for a short curing fire to set the factory paint, so follow the manual’s instructions. Then schedule the final inspection.
What it costs
Costs depend on your region, the chimney’s condition and the appliance you choose. These are typical ranges:
- Wood insert: about $3,500 to $7,000 or more, installed.
- Liner alone: about $1,000 to $3,000, installed, depending on height and insulation.
- Freestanding stove: costs vary widely with the chimney, the hearth and any structural work.
Ask every installer for a written quote that lists the liner, the appliance, the hearth work, the permit and the inspection.
On incentives: the US federal 25C tax credit (30%, up to $2,000) ended for installations after December 31, 2025. Check state and local rebates, which may still apply.
EPA limits for new wood heaters
The EPA’s 2020 (Step 2) limit for new wood heaters is 2.0 grams per hour on the crib wood test, or 2.5 grams per hour on the cordwood test. Choose a unit certified to these limits. Some areas allow only certified appliances, so check your local rules before you buy.
Common misconceptions
- “You can slide a stove into the fireplace and vent it into the existing flue.” It needs a liner sized to the appliance.
- “Any fireplace can take an insert.” Factory-built (zero-clearance) fireplaces need an insert that is listed for them and approved by the maker.
- “Bigger stove means more heat.” An oversized stove runs smoldering, and that builds creosote.
- “A masonry chimney is fine if it looks fine.” Cracks and missing mortar often need a camera inspection to find.
Safety
- Install a carbon monoxide alarm and smoke alarms. Check that the CO alarm is near the appliance.
- Sweep the old flue before the first fire.
- Never overfire. If the appliance or its connector glows red, close the air control and follow the manual.
- Burn only dry wood. Wet wood produces smoke and creosote.
Frequently asked questions
How much does it cost to convert a fireplace to a wood-burning stove?
For an insert, expect roughly $3,500 to $7,000 or more installed, with the liner alone adding about $1,000 to $3,000. Costs vary by region and by the chimney’s condition. Ask for an itemized quote.
How much does it cost to convert an open fireplace to a wood-burning stove?
The cost is similar to converting any masonry fireplace. An open fireplace nearly always needs a liner, because its flue is much larger than a stove’s. Plan for the liner, the appliance, the hearth work and the permit.
What is the 3-2-10 rule for wood stoves?
The 3-2-10 rule is a common chimney-height guideline. It says the chimney should extend at least 3 feet above the point where it passes through the roof, and at least 2 feet higher than any part of a roof or building within 10 feet horizontally. Local codes set the final requirement, so check with your building department before you build or raise a chimney.
Why are people getting rid of wood stoves?
Owners give a range of reasons, and some of them shape how they decide whether to keep or remove a stove. For a closer look at the question, see why people are getting rid of wood stoves.
Related guides
- Converting between gas and wood covers switching fuel in either direction.
- Removing or permanently closing a wood-burning fireplace covers the options if you’d rather not keep the fireplace.
- Why your fireplace insert isn’t heating the room covers the most common causes of poor heat after the install.