Inserts and Conversions

How to get rid of a gas fireplace?

Remove a gas fireplace safely: identify the type, have a licensed fitter cap the gas line, remove the unit, and close the opening. Costs included.

On this page
  1. Quick answer
  2. Identify your gas fireplace first
  3. Step 1: Shut off the utilities
  4. Step 2: Have a licensed fitter cap the gas line
  5. Step 3: Disconnect the electrics
  6. Step 4: Remove the unit
  7. Step 5: Close and patch the opening
  8. What it costs
  9. Permits, warranties and insurers
  10. What to do afterward
  11. Safety

Quick answer

Removing a gas fireplace is a sequence of steps. Shut off the utilities, have a licensed gas fitter cap and test the gas line, disconnect the electrics, remove the unit and its venting, then close and patch the opening. The gas and electrical work must be done by licensed professionals, and the steps differ depending on whether the fireplace uses gas logs, a gas insert or a factory-built unit.

Identify your gas fireplace first

The removal steps depend on what you have:

  • Gas logs in a masonry fireplace. The logs and burner come out, the gas line is capped, and the fireplace can go back to wood after a Level 2 chimney inspection.
  • Gas insert. The surround comes off, the unit is disconnected and pulled out, and the liners are removed from the chimney.
  • Factory-built direct-vent or B-vent unit. The unit and its vent pipe come out, and the roof or wall termination is patched. The opening is then framed and drywalled.

Step 1: Shut off the utilities

Turn off the gas at the appliance valve. If needed, shut it off at the meter or the tank as well. If the unit has a blower, fan or electronic ignition, switch off the circuit at the main panel.

Step 2: Have a licensed fitter cap the gas line

A licensed gas fitter or plumber should disconnect and cap the line, ideally at the tee or source rather than only at the fireplace valve. The line is then leak tested. Many areas require a gas permit for this work. Don’t attempt the gas connection yourself.

Step 3: Disconnect the electrics

Disconnect the blower, the ignition module and the switch circuit. If the unit is hardwired, an electrician should do this.

Step 4: Remove the unit

  • Gas logs. Cap the line first, then lift out the logs and the burner.
  • Insert. Remove the surround, disconnect the unit, pull it out, and remove the liners from the chimney.
  • Factory-built unit. Remove the unit and the vent pipe. Patch the roof or wall termination.

Remove decorative pieces, such as glass panels and artificial logs, to make the unit lighter to move.

Step 5: Close and patch the opening

Seal the old vent termination so water and pests can’t get in. If the opening is being closed, frame it, drywall it, and finish the surface. If you plan to reuse the chimney, have a Level 2 inspection before any new appliance goes in.

What it costs

These are typical ranges, and they vary by region and by the work involved:

  • Gas logs: about $100 to $500.
  • Insert removal: about $300 to $1,000.
  • Full built-in removal and patch: about $1,000 to $3,000 or more.

The gas line work is a separate cost, and it’s usually where the licensed work is billed.

Permits, warranties and insurers

Check these before you start:

  • Permits. Gas work and major changes often need a permit with inspection.
  • Warranties and HOA rules. A home warranty, or an HOA, may limit changes or require specific contractors.
  • Insurer. Some insurers want to know about major changes to heating appliances.

What to do afterward

Once the fireplace is out, you have a few options:

  • A wood-rated fireplace or stove. This requires a Class A chimney, a hearth extension, and the clearances set by the appliance’s label.
  • An electric unit. This needs an outlet and, usually, an electrician. See replacing a wood fireplace with electric.
  • A closed wall. Frame and finish the wall.

Don’t reuse a gas vent pipe for wood. Gas venting isn’t rated for wood smoke. For the wood route, see converting between gas and wood.

Safety

  • If you smell gas, leave the building, don’t operate switches, and call the gas utility from outside.
  • Keep a carbon monoxide alarm with any fuel-burning appliance that stays.
  • Leak test any new gas piping.

The complete guide to inserts and conversions

Converting a Fireplace to a Wood Stove: Options, Costs and Steps
Read the guide

Keep exploring

Guides from other topics

All topics →