Inserts and Conversions

Converting Between Gas and Wood: Swapping Your Fireplace Fuel

Gas to wood or wood to gas? Learn what your fireplace can take, what each switch costs, and the permits, gas work and chimney upgrades you'll need.

On this page
  1. Quick answer
  2. Start by identifying your fireplace
  3. Converting gas to wood in a masonry fireplace
  4. Converting a factory-built gas fireplace to wood
  5. Replacing a gas fireplace with a wood stove
  6. Going from wood to gas
  7. What it costs
  8. Permits, inspection and safety

Quick answer

Whether you can switch depends mainly on how the fireplace is built. A masonry fireplace with gas logs added can usually go back to wood. A factory-built gas fireplace can’t be converted in place; it has to be removed and replaced with a unit rated for wood. Switching from wood to gas is also a major job, and it always needs a licensed gas installer.

Start by identifying your fireplace

Two questions decide the job:

  1. Is the firebox masonry or factory-built? A brick, stone or block firebox with gas logs in it can usually take wood again. A factory-built metal firebox can’t.
  2. What is the existing venting? A gas vent pipe, whether B-vent or a direct-vent coaxial pipe, isn’t rated for wood smoke. Wood needs a chimney rated for solid fuel, such as a lined masonry chimney or a Class A chimney system tested to UL 103HT, which is rated to 2,100°F.

A vent-free gas unit has no chimney at all. Converting one to wood means installing a complete wood-rated chimney system.

Converting gas to wood in a masonry fireplace

Treat this as a general outline. A licensed installer and a chimney professional should lead the work.

  1. Inspect first. Have a certified chimney sweep carry out a Level 2 inspection. NFPA 211 requires one when the fuel type changes, and it often includes a video scan of the flue.
  2. Cap the gas line. A licensed gas fitter disconnects the supply, caps the line and runs a pressure test. Gas work is licensed work, not a DIY job.
  3. Remove the gas equipment. Take out the gas logs, burners and hardware.
  4. Restore the damper. The damper must open and close properly for wood. Vented gas logs often have a damper clamp that holds the damper fixed open, so that clamp has to come off.
  5. Sweep and line the chimney. If the existing flue isn’t suitable, install a stainless steel liner. For wood, the liner is usually 316Ti or 316L stainless, UL 1777 listed, and it runs the full length from the appliance to the top of the chimney. Its diameter normally matches the appliance’s flue collar, often 6 inches.
  6. Fit a suitable grate, if you’re burning open logs. Use a heavy iron grate rated for wood. Make sure the damper opens fully.
  7. Get the permit and final inspection. Most jurisdictions require a permit for solid-fuel work. Insurers may ask for proof of a permitted install.

Expect the cap and inspection to cost roughly $200 to $1,000. A stainless liner alone often runs $1,000 to $3,000 installed, depending on region and chimney height.

Converting a factory-built gas fireplace to wood

A factory-built gas fireplace, whether direct-vent or B-vent, can’t be converted to burn wood. Its firebox and venting weren’t built for wood fire temperatures. Your options are:

  • Remove the unit and its venting, then install a zero-clearance wood fireplace listed for wood, with a Class A chimney.
  • Remove the unit and install a wood stove or insert that suits the space, with a chimney rated for wood.

Either way, the old gas vent can’t be reused for wood smoke. Don’t burn wood or paper in a gas appliance.

Replacing a gas fireplace with a wood stove

A freestanding stove needs a noncombustible hearth pad and clearances to combustible walls, as set out on the stove’s label. Ember protection is typically 16 to 18 inches in front and about 8 inches at the sides, but the label governs. A wood stove insert slides into a masonry firebox instead, and it needs a liner sized to the insert.

Either way, you’ll usually need a new Class A chimney or liner, a hearth pad, and the correct clearances. For a related look at the chimney side, see converting a fireplace to a wood stove.

Going from wood to gas

There are three main ways to add gas to a wood fireplace:

  • Vented gas logs. These use the existing chimney. The damper must be fixed open to the standard (ANSI Z21.60), usually with a damper clamp. Vented logs are mostly decorative, and they lose heat up an open flue.
  • Direct-vent gas insert. This runs two liners (an intake and an exhaust, often about 3 inches each) or a co-linear kit up the chimney. Efficiency is roughly 70% to 85%. Installed costs are often about $3,000 to $6,000.
  • Vent-free logs or an insert. These don’t need a chimney for venting. Vent-free logs must meet ANSI Z21.11.2, are limited to 40,000 Btu/h, and have an oxygen-depletion sensor. Some states and cities ban or restrict them, so check locally first.

Whichever you choose, the gas line may need to be run to the fireplace. That often costs $250 to $1,000 or more. Natural gas and propane units aren’t interchangeable. Switching between them needs a manufacturer’s conversion kit.

For the installation side of a gas install, see how hard it is to add a gas fireplace to an existing home.

What it costs

These are rough ranges. They vary by region and by the work involved.

Conversion Typical cost Notes
Gas logs to wood, masonry fireplace About $200 to $1,000 Gas capping, sweep and inspection. A liner is extra.
Factory-built gas unit to wood About $4,000 to $15,000 or more Removal, a wood-rated chimney and the new appliance
Wood to gas, direct-vent insert About $3,000 to $6,000 installed Gas line run is extra, often $250 to $1,000 or more

Compare the running costs of wood and gas against your local fuel prices before you decide.

Permits, inspection and safety

  • Most jurisdictions require permits for both gas and solid-fuel work. Gas installs also need a leak and pressure test.
  • Install a carbon monoxide alarm and smoke alarms. Check the CO alarm near the appliance.
  • Never burn wood or paper in a gas appliance.
  • Capping gas lines and testing for leaks are licensed work.

If you’re still deciding whether to remove the gas fireplace entirely, how to get rid of a gas fireplace covers the removal side. For the broader choice between a stove and a fireplace, see the pillar guide to converting a fireplace to a wood stove.

The complete guide to inserts and conversions

Converting a Fireplace to a Wood Stove: Options, Costs and Steps
Read the guide

Keep exploring

Guides from other topics

All topics →