Short answer
A wood fireplace is safest when you burn dry wood, light and run the fire properly, keep the damper and flue working, clean ashes safely, and have the chimney inspected every year. This guide covers each step and links to the deeper guides.
Choose and store dry wood
Burn wood with a moisture content below about 20 percent. Seasoned softwoods such as pine usually need about 6 to 12 months to dry, and dense hardwoods such as oak often need one to two years. Time alone is not a reliable test, so use a moisture meter if you can. Stack the wood off the ground, cover only the top, and leave the sides open to the air.
Do not burn trash, treated or painted wood, particleboard, or plywood. For the full list, see what not to burn in a fireplace. For drying times and how to test wood, see how long firewood should sit before burning.
Before you light
- Open the damper fully and check that it moves freely. Keep it open for the whole fire.
- If cold air is coming down the flue, prime it by holding a lit, rolled piece of newspaper near the damper for a few seconds.
- Check that the screen or glass doors are in place.
- Make sure smoke alarms and carbon monoxide alarms are working.
- Keep furniture, rugs, curtains and decorations at least 3 feet from the opening.
Build and light the fire
Use a top-down layout. Put the largest splits on the bottom, smaller splits above them, and kindling and tinder on top. Light the top. Small, hot, bright fires make less creosote than large, smoldering ones.
Do not use gasoline, kerosene or lighter fluid to start a fire. Keep fire starters to dry kindling or a commercial starter made for fireplaces.
Keep the fire well-behaved
- Keep the damper fully open while the fire burns. Do not partly close it to slow the fire.
- Keep a metal screen or glass doors in place whenever a fire is burning.
- Burn at a normal rate. Overfiring can crack firebrick and damage the chimney.
- Never leave a fire unattended, and never go to sleep with an open fire still burning.
- Keep a Class A or ABC fire extinguisher nearby.
If the fire smokes heavily, check the damper, the wood and the draft before you add more fuel.
Clean out ashes safely
Leave about 1 inch of ash on the firebox floor to insulate the coals and help the next fire start. Remove ash once it builds up to the grate.
Remove ash only after the fire has been out for several hours, ideally overnight, and the ash is fully cold. Shovel it into a metal can with a tight-fitting lid. Set the can on a noncombustible surface at least 10 feet from the house, decks, wood piles and other buildings. Ash can stay hot enough to ignite for several days. For the full process, see how to put out a fireplace fire safely.
Sweep and inspect
Have the chimney inspected every year, as NFPA 211 recommends. Sweep whenever soot or creosote reaches about 1/8 inch on the flue walls. For how often that is, see how often to sweep a chimney.
Between sweeps:
- Replace cracked firebrick, and repair mortar joints with refractory mortar.
- Check that the chimney cap and its spark arrestor mesh are in good repair. Mesh openings should generally be 3/8 to 1/2 inch.
- Inspect the damper for rust, warping and a full seal.
- Look for tar-like buildup, flakes, or a dirty chimney. For the signs, see what are the signs of a dirty chimney.
Creosote is the deposit that fuels most chimney fires. For how it forms, see creosote in your chimney.
Alarms and ventilation
Install smoke alarms and carbon monoxide alarms on every level, and outside each sleeping area. Test them monthly. Fireplaces can release carbon monoxide if the damper is closed too early or the flue is blocked. For details, see can a wood burning fireplace cause carbon monoxide poisoning.
In a tight house, crack a window in the room with the fireplace if smoke spills back into the room. Fresh air helps the fire draw properly.
When to stop and call a professional
Stop using the fireplace and call a qualified chimney professional if you notice:
- glazed, shiny creosote, or deposits that come back quickly after cleaning
- a blockage, nest or debris in the flue
- cracked flue tiles or a damaged liner
- smoke that regularly spills into the room
- signs of a chimney fire, even a small one, as described in chimney fires: early warning signs and what to do
Gas fireplaces also need annual service, even though they follow different maintenance steps.
Quick checklist
- Burn dry wood below about 20 percent moisture.
- Open the damper before lighting, and keep it open until the fire is fully out and cold.
- Use a screen or glass doors, and keep combustibles 3 feet away.
- Never leave the fire unattended.
- Remove ashes into a metal can, and keep it 10 feet from the house.
- Test smoke and CO alarms monthly.
- Have the chimney inspected every year, and sweep at about 1/8 inch of buildup.