Wood Fireplace Use and Safety

Chimney Fires: Early Warning Signs and What to Do

Roaring noise, dense smoke or sparks from the chimney top can signal a chimney fire. Learn the warning signs, the first steps to take, and how to prevent one.

On this page
  1. Short answer
  2. What a chimney fire is
  3. Warning signs during a fire
  4. Quiet chimney fires: clues afterward
  5. What to do right away
  6. After a chimney fire: do not use the chimney until inspected
  7. How to prevent chimney fires

Short answer

A chimney fire is a fire burning inside the flue, usually fed by creosote. It can be loud and obvious, or quiet and slow. Watch for popping or roaring sounds, dense smoke, sparks or flames from the top of the chimney, and a hot, acrid smell. If you think a chimney fire has started, get everyone out and call 911 first.

What a chimney fire is

Creosote is a tar-like deposit that forms in the flue when wood smoke cools and condenses. When it ignites, the flue can reach very high temperatures. CSIA guidance notes that chimney fires can exceed 2,000°F. That heat can crack flue tiles and liners, warp metal parts, and ignite nearby framing.

Warning signs during a fire

  • Sound: popping, cracking or banging, or a deep roar that people often compare to a freight train or jet engine.
  • Smoke and sparks: thick smoke from the chimney top, smoke at the joints of the chimney, or flames and sparks shooting out of the top.
  • Heat and smell: an intense, hot, acrid smell, a stovepipe or chimney that glows or is too hot to touch, or pipes that shake as the fire grows.

Quiet chimney fires: clues afterward

Some chimney fires burn slowly and go unnoticed. You may find these clues later, or during an inspection:

  • puffy, honeycombed, or flaky creosote in the flue
  • creosote flakes on the roof or the ground below the chimney
  • a warped or heat-discolored cap, damper or metal pipe
  • cracked flue tiles or new cracks in the masonry

If you see any of these, stop using the chimney and have it inspected. The chimney may look fine from the outside.

What to do right away

  1. Get everyone out. Call 911 or your local emergency number from outside. Do not stay to fight the fire.
  2. Cut the air supply, if it is safe. Close the stove air controls or fireplace glass doors. Do this only if it does not delay your exit.
  3. Do not spray water into a hot stove or flue. Thermal shock can crack the liner or the appliance, and the steam can cause a backblast.
  4. Stay off the roof. Leave work outside the house to firefighters.

Chimney fire suppressant flares, such as Chimfex, are designed for use in the firebox. Follow the label. They are not a reason to delay calling for help.

After a chimney fire: do not use the chimney until inspected

A chimney that looks intact can still have cracked liners. The idea that a chimney survived, so it must be fine, is wrong. Have a Level 2 inspection by a CSIA-certified sweep before you use the chimney or appliance again. This is also the right step after a small fire.

How to prevent chimney fires

  • Burn dry wood. Use wood below about 20 percent moisture. See how long firewood should sit before burning.
  • Avoid smoldering fires. Run hot, bright fires with plenty of air, rather than letting wood smolder overnight.
  • Sweep on schedule. Sweep when creosote reaches about 1/8 inch, and have the chimney inspected every year. For how often, see how often to sweep a chimney.
  • Cap and screen the chimney. A cap with spark arrestor mesh keeps sparks in and animals out. Mesh openings should generally be 3/8 to 1/2 inch.
  • Check the masonry each year. Replace cracked firebrick, and repair joints with refractory mortar.

For more on the deposit that fuels these fires, see creosote in your chimney.

The complete guide to wood fireplace use and safety

Wood Burning Fireplace Tips: Using and Maintaining Your Fireplace
Read the guide

Keep exploring

Guides from other topics

All topics →