A wood burning fireplace is built in one of two ways. It can be a masonry structure assembled on site, or a factory-built unit that is manufactured to a safety listing and installed into a framed opening. Both work, but they differ in weight, cost, timeline, and how much of the job a homeowner can reasonably do.
This guide covers the main parts, the minimums that building codes set, and where the practical limits of a DIY project are. It is an overview. The linked articles go deeper on each question.
Two ways a wood fireplace gets built
Site-built masonry fireplaces are made on location from brick, stone, or concrete block. The firebox is lined with firebrick and set in refractory mortar. These fireplaces are heavy and permanent, and they can be customized to almost any design. They also take the longest to build, need a full footing and chimney, and depend heavily on the mason’s workmanship. For the build order, see how fireplaces are constructed.
Factory-built (prefabricated) fireplaces use a metal firebox that is tested and listed to a safety standard for wood-burning units. In the United States the common standard is UL 127. The unit sits on a framed floor, is enclosed in a framed chase, and is vented through a listed chimney system. These units are lighter, faster to install, and more consistent from one unit to the next. They must be installed with the maker’s listed parts and clearances. For a side-by-side comparison, see prefab vs site-built fireplaces.
Gas and electric fireplaces follow different rules and are not covered in depth here.
The parts, from the footing up
Footing and hearth base
A masonry fireplace needs its own reinforced concrete footing. The footing has to sit below frost depth, on undisturbed soil or properly engineered fill. It cannot rest on floor joists. The hearth is the noncombustible surface in front of the opening, and it needs noncombustible support underneath. More detail is in what foundation a fireplace needs.
Firebox
The firebox is where the fire burns. In a masonry fireplace it is built from firebrick, not common brick or concrete block, because ordinary masonry can crack under sustained high heat. Firebrick is laid in refractory mortar made for high temperatures. Codes set minimum wall thicknesses and depths, which are summarized in the table below.
Throat and damper
Above the firebox opening is the throat, which narrows toward the flue. A metal damper sits in or just above the throat and controls airflow. Codes require a damper in masonry fireplaces. Keep the damper open while a fire is burning. Close it only after the fire is out and the embers have cooled, so that smoke and carbon monoxide cannot drift back into the room.
Smoke chamber and flue
The smoke chamber sits above the damper. It narrows upward, like an inverted funnel, to guide smoke into the flue. The flue is the vertical passage through the chimney, lined with clay tiles or a listed metal liner. The liner should sit apart from the surrounding masonry with an airspace. Filling that gap with mortar is a known mistake.
Chimney, crown and cap
The chimney carries smoke above the roof. Masonry chimneys are usually finished with a sloped concrete crown that sheds rain, and often a spark arrestor cap. Chimney height is set by the 3-2-10 rule, which is explained in the 2 + 10 rule article.
Surround and mantel
The surround and mantel make up the decorative face. Codes limit how close combustible material can sit to the opening, and how far a mantel or trim can project near it. The exact distances are in standard fireplace dimensions.
Key minimums to know
The table below lists typical minimums from the residential building code for masonry fireplaces. Treat it as a starting point, not a design guide. Your local code, the appliance listing or manual, and a licensed professional set the actual requirements.
| Item | Typical minimum |
|---|---|
| Footing | At least 12 in thick, extending 6 in past the fireplace on all sides |
| Firebox depth | At least 20 in (Rumford-style fireboxes have their own, smaller minimum) |
| Firebox walls | 8 in total, including at least 2 in of firebrick lining (10 in if unlined) |
| Throat | At least 8 in above the top of the opening |
| Hearth | At least 4 in thick |
| Clearance from combustible framing | 2 in at the front and sides, 4 in at the back |
| Chimney height | 3 ft above the roof penetration and 2 ft above anything within 10 ft |
Can you build one yourself?
The answer depends on the type of fireplace:
- Electric units are the simplest indoor option. Plug-in and wall-mounted units need no chimney or gas line. A built-in media wall is mostly carpentry, and any wiring should be done to local electrical rules, which may require a licensed electrician.
- Factory-built wood or gas units are often installed by a licensed contractor, because the framing, clearances, and venting must match the listing exactly. A homeowner with solid carpentry skills may handle the framing and finish work. Gas connections and chimney work are a different level of job.
- Site-built masonry is a major structural project. It needs a footing, heavy masonry, a permit, inspections, and skilled work on the firebox and flue. For most homeowners it is a job for a licensed mason or contractor.
A masonry fireplace is a poor first building project for most people. The structure is heavy, the fire is hot, and mistakes in the firebox, flue, or clearances can lead to house fires or carbon monoxide entering the home.
Permits, inspections and clearances
Most wood-burning fireplace and chimney projects need a permit. Inspections are often required at key stages, such as the footing, the firebox and chimney, and the final check. Codes change by local amendment, so check with your building department before buying materials.
Some air-quality districts restrict new wood-burning devices, and some areas restrict them in new construction. Check this before you commit to a wood-burning unit. Your homeowners insurer should also know about the project, since some policies have requirements for solid-fuel heating.
Clearances protect the house from heat. Keep combustible framing, drywall, and furniture back by the distances in the manual and the code.
Curing and first fires
New masonry needs time to cure before it takes a full fire. Mortar and concrete hold moisture, and a sudden hot fire can crack the masonry. Follow the mason’s or manufacturer’s curing schedule. This usually means a series of small fires over several days, building up gradually. A factory-built unit follows the break-in instructions in its manual.
Once the fireplace is in use, burn only dry, seasoned hardwood. Wood with a moisture content under about 20 percent burns more cleanly and leaves less creosote in the chimney. Install smoke and carbon monoxide alarms, and have the chimney inspected at least once a year.
Choosing a route
Use this as a rough guide:
- You want the easiest indoor fire and have no chimney. Consider an electric unit, or a direct-vent gas unit if you can run a gas line and vent through a wall. See can you put a fireplace into a house.
- You want a real wood fire and have a set budget. Consider a factory-built unit installed to its listing.
- You want a custom, heavy, long-lived masonry fireplace. Plan for a licensed mason, a permitted footing and chimney, and a longer timeline.
- You want an outdoor fireplace instead. See building an outdoor stone fireplace.
- You live in a manufactured home. The rules are different and stricter. See fireplaces in manufactured homes.
Common questions
Can you put a fireplace into a house?
Yes, in most houses. The venting route decides which type fits. Electric and direct-vent gas units are the least invasive. Factory-built wood units need a listed chimney. Masonry is the most involved. Read can you put a fireplace into a house? for the options.
How much does it cost to build a fireplace?
Costs range from a few hundred dollars for a plug-in electric unit to tens of thousands for a masonry fireplace with a full chimney. Prices vary by region and finish. See how much it costs to build a fireplace for the breakdown by type.