A prefab, or factory-built, fireplace is manufactured and listed as a unit, then installed into a framed opening. It is usually faster and less expensive to install. A site-built masonry fireplace is built brick by brick on location. It is heavier, takes longer, costs more, and can be fully customized. With care, it can last for generations.
What each one is
Prefab (factory-built). The firebox is a metal unit that has been tested and listed. Wood units are listed to UL 127, and gas units are listed to the gas standards, such as ANSI Z21.50 or Z21.88. The unit is lightweight, usually a few hundred pounds, and sits on a framed floor. “Zero-clearance” means it can be framed with combustible materials at the standoff distances the listing specifies. Replacement parts must be the maker’s listed parts.
Site-built masonry. The fireplace and chimney are built on location by a mason. Together they often weigh several tons, so they need a reinforced footing. The work is governed by the residential code. It allows the most design freedom, and it can be repaired and relined over time.
Side-by-side comparison
| Prefab (factory-built) | Site-built masonry | |
|---|---|---|
| Typical installed cost | Roughly $3,000 to $10,000 for a wood unit | Roughly $10,000 to $30,000 or more |
| Install time | Often 1 to 3 days, plus finishing | Often 1 to 3 weeks or more, plus curing |
| Weight and footing | A few hundred pounds, on a framed floor | Several tons, needs a reinforced footing |
| Design freedom | Standard sizes, with finish options within the listing | Almost unlimited |
| Efficiency | Modern EPA-certified prefab wood units run well above open masonry | Open masonry fireplaces are typically around 10 percent efficient or less |
| Lifespan | Often about 20 to 30 years, depending on the model and use | Often 50 to 100 years or more, with maintenance |
| Repairs | Usually a parts replacement, or replacing the whole system | Can be repaired and relined |
These figures are approximate. They vary by region, model, and finish.
Cost and timing
Prefab units cost less and install faster because most of the manufacturing happens in a factory. The unit arrives tested and largely complete, so site work is mainly framing, venting, and finishing.
Masonry takes longer because it is built by hand on site. It also needs a footing and curing time before a full fire. Factor the calendar into your planning, not just the price.
Durability, repairs and lifespan
Masonry is made from heavy, durable materials, but it still needs maintenance. Crowns, mortar joints, liners, and flashing all need upkeep. Masonry can be repaired and relined when it wears.
A prefab unit is built to its listing and must be maintained the same way. Its metal parts can warp if the fire is too large or the unit is overfired. Replacement parts must be the ones for that model, and some models are discontinued, which can make parts hard to find. When a prefab wears out, it is usually replaced as a system.
Lifespan estimates vary by model and use. Some sources give shorter figures for prefab units than the range above, so treat any single number as an estimate.
Efficiency and heat
An open masonry fireplace sends much of its heat up the chimney. Masonry mass also releases heat slowly after the fire has gone out, which many people like. Prefab units are engineered to deliver more of their heat into the room, using insulation, air-cooled pipes, and sometimes blowers. EPA-certified wood units are generally more efficient than open fireplaces.
The middle ground: modular masonry kits
Listed modular masonry systems, made from refractory or pumice panels, give a masonry look with a listed assembly. They can shorten the build compared with a full masonry project. Check that the kit is listed for the use you have in mind, and follow its instructions exactly.
Common myths
- “Prefab is unsafe.” A prefab unit is safe when it is installed to its listing with listed parts.
- “You can put any heavy stone surround on a prefab.” Surrounds must stay within the listed clearances and load limits.
- “Masonry is maintenance-free.” It is not. Crowns, mortar, liners, and flashing all need upkeep.
- “A prefab can burn anything a masonry fireplace can.” Follow the manual for fuel and log length. Overfiring damages the panels.
Which to choose
- Pick a prefab unit if you want faster, lower-cost installation and consistent engineering, and you are comfortable using listed parts for the life of the unit.
- Pick site-built masonry if you want a fully custom, long-lived structure and have the budget and time for it. The site also needs a suitable footing. See what foundation a fireplace needs.
- Consider a modular masonry kit if you want the masonry look with a shorter build.
- Either way, plan on a licensed installer, a permit, and an inspection. For the full overview, see wood burning fireplace construction. For what each option costs, see how much it costs to build a fireplace.