Wood Stoves

Wood Burning Furnaces for Homes: How They Work and What to Buy

Learn how indoor wood furnaces and outdoor wood boilers heat a whole house, how much wood they burn, and what to check before you buy one.

On this page
  1. Indoor forced-air wood furnaces
  2. Outdoor wood boilers and wood furnaces
  3. Gasification boilers and thermal storage
  4. How much wood does a whole house use?
  5. Efficiency and emissions
  6. Power, backup and safety
  7. Costs
  8. How to choose
  9. Which brand is most reliable?
  10. Common misconceptions

A wood burning furnace heats a whole house in one of two ways. An indoor furnace heats air and moves it through ductwork with a blower. An outdoor wood boiler heats water in a separate unit outside, then pumps the water through insulated underground pipes to radiators, radiant floors or a water-to-air coil. Both need listed equipment, and both need electricity for their fans or pumps, so plan for power outages.

Indoor forced-air wood furnaces

An indoor wood furnace burns wood in a firebox and heats air that a blower pushes through the house’s ductwork. Some are installed as add-on furnaces beside an existing oil, gas or electric furnace, sharing the same ducts. Local code may restrict that arrangement, so check before you plan around it.

Indoor units need their own dedicated flue. Don’t vent one into a flue shared with another appliance unless the listing allows it. Install carbon monoxide alarms near the furnace and in sleeping areas.

Outdoor wood boilers and wood furnaces

An outdoor wood boiler is a separate shed-like unit, typically 50 to 150 feet or more from the house. It heats water, which travels through insulated underground PEX lines to supply heat or domestic hot water. The fire is outside the house, but the smoke still reaches your neighbors, and many towns and states set setback, stack-height or ban rules for these units.

Outdoor boilers need water treatment and freeze protection for the lines.

Gasification boilers and thermal storage

A gasification boiler burns wood gases at high temperature. It is usually paired with a thermal storage tank, often 500 to 1,000 or more gallons depending on the system. Without storage, a gasification boiler tends to idle and smoke. With storage, certified units can reach about 80% efficiency or more, depending on the test.

How much wood does a whole house use?

Whole-house wood heat often burns about 4 to 10 cords a season. The figure depends on your climate, the size and insulation of the house, and the appliance. For the basics of cords and how to estimate use, see our guide to how much firewood a wood stove burns per year.

Efficiency and emissions

Certified furnaces are typically about 60 to 75% efficient. Gasification boilers with storage are often 80% or more, depending on the test method. EPA’s 2020 Step 2 limits are 0.15 lb of particulate per million BTU of heat output for forced-air furnaces, and 0.10 lb per million BTU for hydronic heaters. Confirm the limit that applies to your unit’s burn rate.

Older uncertified outdoor boilers are known for heavy smoke. Check the certification of any unit before you buy it.

Power, backup and safety

Most wood furnaces and boilers need electricity for blowers or pumps. Plan for outages with battery backup or a gravity-safe design. An over-temperature limit and a power-failure heat dump, or a gravity design, are essential for safe operation. A listed appliance with its own dedicated flue and the right clearances is the starting point.

Costs

Installed costs vary widely with the system and the house. In the US, an indoor forced-air wood furnace typically runs roughly $4,000 to $10,000 installed. An outdoor boiler typically runs roughly $10,000 to $25,000 or more. Add the cost of wood or a wood supply, labor, and electricity for pumps and blowers.

Wood furnaces don’t save money everywhere. The savings depend on your wood source and how much of the work you do yourself.

How to choose

  • Get a heat-loss calculation. A calculated heat load is more reliable than a square-foot guess. For the general method, see our guide to sizing a wood stove.
  • Check the listing. Use a listed appliance and follow the clearances on its label.
  • Ask about service. Find out who installs and services the unit near you, and which parts they stock.
  • Plan for backup. Decide how the house stays warm if the power or the fire goes out.
  • Check local rules. Setback and stack-height rules can decide where an outdoor unit can go.

Which brand is most reliable?

The information available here does not support naming one brand as the most reliable. Reliability depends on the model, the installer and the service network near you. Ask dealers for references, read the warranty and parts coverage closely, and treat owner reviews with care. For brand-level efficiency figures, see which wood stove brand is the most efficient.

Common misconceptions

  • “An outdoor boiler is cleaner because it’s outside.” The smoke still affects neighbors.
  • “A wood furnace is just a stove with ducts.” It needs a listed furnace and its own flue.
  • “Gasification doesn’t need storage.” Without storage it idles and smokes.
  • “Wood furnaces save money everywhere.” That depends on your wood source and labor.

Insurers may underwrite these systems differently from indoor stoves. See our guide to whether house insurance goes up with a wood stove before you buy.

The complete guide to wood stoves

Wood Burning Stove vs Fireplace: Heat, Cost and Efficiency Compared
Read the guide

Keep exploring

Guides from other topics

All topics →