A wood stove typically burns about 1 to 6 cords of firewood a year. Supplemental use in a mild climate sits near the low end, and primary heat in a cold climate sits near the top. A full cord is 128 cubic feet. To estimate your own use, divide your seasonal heat need by the heat in a cord of your wood, multiplied by the stove’s efficiency.
Cords, face cords and what you’re buying
A full cord is a stack of 128 cubic feet, measured as 4 feet by 4 feet by 8 feet. A face cord, sometimes called a rick, varies by region. It is 4 feet by 8 feet by one log length, so with 16-inch logs it is about one-third of a cord. Check whether a seller means a full cord or a face cord before you pay.
A loosely or crookedly stacked pile holds less wood than a tight, square one, so measure the stack rather than judging it by eye.
Typical use by climate and role
| Use | Typical seasonal use |
|---|---|
| Supplemental heat | About 1 to 3 cords |
| Primary heat, mild climate | About 1 to 3 cords |
| Primary heat, cold climate (for example, New England or the upper Midwest) | About 3 to 6 cords for a typical 1,500 to 2,500 sq ft home |
These are typical ranges. The house, its insulation and the stove all change the result.
Estimate your own use
Use this formula:
cords = seasonal heat need (BTU) ÷ (heat per cord × stove efficiency)
For example, suppose your home needs 60 million BTU a season, your wood gives about 22 million BTU per cord, and the stove runs at 70% efficiency. Then you need about 3.9 cords: 60 ÷ (22 × 0.70) ≈ 3.9. The 60 million BTU figure is only an example.
Your seasonal heat need comes from a heat-loss calculation, which is more accurate than a square-foot estimate. For the sizing method, see our guide to what size wood stove you need.
How wood species change the count
Heat per cord varies by species. These are approximate values at about 20% moisture:
| Species | Approximate heat per cord |
|---|---|
| Hickory | 27 to 28 million BTU |
| White oak | 25 to 29 million BTU |
| Red oak | About 24 million BTU |
| Sugar maple | 24 to 25 million BTU |
| Ash | 23 to 24 million BTU |
| Douglas fir | About 21 million BTU |
| Birch | 20 to 21 million BTU |
| Elm | About 20 million BTU |
| Red maple | About 19 million BTU |
| Aspen and cottonwood | 15 to 18 million BTU |
| White pine | 14 to 16 million BTU |
Softwoods hold less heat per cord, but about the same heat per pound as hardwoods, so they are still useful. Dry wood holds roughly 8,600 BTU per pound on a higher heating value basis.
Moisture and stove age
Wet wood, at 30% moisture or more, wastes energy boiling off water, so you burn noticeably more wood for the same heat. Keep wood at 20% moisture or less.
Older stoves, those made before 1990, use roughly 50% more wood than EPA-certified stoves. Open fireplaces burn a lot of wood for little heat, at about 10% efficiency or less. For how to choose between the two, see wood burning stove vs fireplace.
Store firewood properly
Store wood at least one season ahead. Stack it off the ground, cover the top, and leave the sides open so air can move through. Keep woodpiles about 20 to 30 feet from the house to reduce pest and fire risk, though local advice varies.
Whole-house heating uses more
A furnace or boiler that heats the whole house often burns more wood than a stove that heats one room. Whole-house systems commonly burn about 4 to 10 cords a season. For those systems, see wood burning furnaces for homes.
Common misconceptions
- “Softwood is useless.” It has less heat per cord but about the same per pound.
- “A face cord is a cord.” A face cord is about one-third of a full cord.
- “Bigger stoves burn more wood.” The heat load drives consumption, not the stove size alone.
- “Stacked volume is exact.” Loose or crooked stacking cuts the real amount.