Wood Stoves

Why Your Wood Stove Keeps Going Out and How to Keep a Fire Burning

A wood stove that keeps going out is usually wet wood, air turned down too soon or a weak draft. Learn the causes and how to keep the fire burning.

On this page
  1. Check the wood first
  2. Build the fire from the top down
  3. Keep the air open until the wood chars
  4. Warm a cold flue first
  5. Reload without smothering the fire
  6. Check ash, gaskets and draft
  7. Catalytic stoves
  8. When a fire keeps going out
  9. What not to do
  10. Common misconceptions

A wood stove usually goes out for one of four reasons. The wood is too wet, the air was turned down too soon, the chimney isn’t drawing well, or the fire was built with too little small fuel. Check the wood’s moisture first, keep the air open until the wood has charred, warm a cold flue, and reload onto a bed of coals.

Check the wood first

Wet wood is the most common cause. Firewood should be 20% moisture or less, measured on a freshly split face at room temperature. Most hardwoods need about a year split and stacked. Oak often needs two years or more. Softwoods typically need about 6 to 12 months, depending on your climate.

Kiln-dried wood isn’t automatically ready to burn. It can still be above 20% if it has been stored wet. A moisture meter is the simplest check.

Build the fire from the top down

Many owners use a top-down start: larger splits at the bottom, with kindling and fire starters on top. Use kindling about 1 inch thick, and split the fuel into pieces about 3 to 6 inches across. Big unsplit rounds don’t catch well, so split them. Don’t stack logs so tightly that air can’t move between them. If your manual specifies a different start method, follow the manual.

Keep the air open until the wood chars

The most common mistake is turning the air down too early. Wait until the wood is well charred and the stovetop is around 400 to 500°F, which often takes 20 to 30 minutes. Then turn the air down in stages. Shutting the air too soon starves the fire, so it smolders and goes out.

Warm a cold flue first

A cold chimney can trap cold air that pushes down into the stove and chokes the draft. Before you light the main fire, warm the flue. Hold a piece of burning newspaper or a fire starter near the flue outlet, as your manual allows, until the draft starts. Then build the fire.

Reload without smothering the fire

Rake the coals toward the air inlet, add wood onto the hot coal bed, and open the air for 5 to 15 minutes before you turn it back down. Don’t add wood to a fire that is still gassing heavily, and don’t add a large load to a weak fire.

Check ash, gaskets and draft

  • Ash. A thin bed of ash, about 1 inch, helps insulate the fire. A deep pile blocks air from reaching the fuel. Check your manual for the ash depth your stove expects.
  • Gaskets. Leaky door gaskets let air in at the wrong places. Use the dollar-bill test. If the bill slides out easily, replace the gasket.
  • Draft. A short chimney, a plugged cap screen, creosote or exhaust fans that pull air out of the house can all weaken the draft. Our guide to smoke when you open the door covers the draft checks in more detail.
  • Overpacking. Stacking logs too tightly blocks the air between them.

Catalytic stoves

On a catalytic stove, close the bypass only after the catalyst lights, which is about 500°F on the probe thermometer. Closing it too early stalls the fire. Follow the manual for light-off. For how the two designs differ, see our guide to catalytic vs non-catalytic wood stoves.

When a fire keeps going out

If the fire still goes out after you have fixed the wood, air and draft, have the chimney checked. Creosote and blockages are common causes. Smoldering fires build creosote quickly, so get the chimney checked more often if this keeps happening.

Puffing and smoke problems can point to the same air and draft issues. See why smoke puffs out of a wood stove for the signs to watch for.

What not to do

  • Never use gasoline, lighter fluid or kerosene to restart a fire. They can cause a sudden flare-up.
  • Don’t close the air early to make the fire last. It smolders out and builds creosote.
  • Don’t rely on more newspaper. Dry kindling matters more than extra paper.
  • Don’t start with wet wood. Wet bark facing the coals slows ignition, so dry the wood first.

Common misconceptions

  • “Kiln-dried means ready to burn.” It may still be over 20% if it was stored wet.
  • “Shut the air down to make it last.” Too early, and the fire smolders out.
  • “Bark side down doesn’t matter.” Wet bark facing the coals slows ignition.
  • “More newspaper fixes it.” Dry kindling matters more.

The complete guide to wood stoves

Wood Burning Stove vs Fireplace: Heat, Cost and Efficiency Compared
Read the guide

Keep exploring

Guides from other topics

All topics →