Gas Fireplaces

Gas Fireplace Stays On When the Switch Is Off: Causes and Fixes

Gas fireplace stays on when the switch is off? Learn what's normal, how to shut off the gas now, and which switch, remote or valve is at fault.

On this page
  1. Shut It Off Now
  2. What Is Normal After Switching Off
  3. Check the Remote and Receiver
  4. Check the Wall Switch and Wiring
  5. Thermostat Mode and Smart Remotes
  6. A Stuck Valve
  7. When to Call a Technician

If a gas fireplace stays on after you switch it off, shut off the gas first. Then check the remote receiver, the wall switch and the wiring. A stuck valve is the least common cause, but it needs a technician. A standing pilot that stays lit after switching off is normal. Only the main burner should go out.

Shut It Off Now

Don’t wait to find the cause. Do these steps first:

  1. Turn the valve knob to PILOT or OFF.
  2. If the burner keeps running, close the manual gas shutoff on the gas line. The handle should be perpendicular to the pipe when it’s closed.
  3. Leave the fireplace off until a technician has checked it.

Never leave a burner that won’t shut off running unattended.

What Is Normal After Switching Off

Some behavior looks like a fault but isn’t:

  • The pilot stays lit. On a standing-pilot unit, the pilot is supposed to keep burning. Only the main burner goes out.
  • The blower keeps running. A thermal switch keeps the blower on until the unit cools. This can take 10 to 30 minutes or more.
  • The flame lingers. A short delay of a few seconds before the flame drops can be normal on some valves.

A running fan doesn’t mean gas is still flowing.

Check the Remote and Receiver

Many fireplaces with a remote have a three-position slide switch on the receiver: ON, REMOTE and OFF. In the ON position, the burner ignores the remote and the wall switch. If the flame keeps running after you use the remote to turn it off, check that the receiver is set to REMOTE and not ON.

A stuck receiver relay can also keep the burner on. To reset it, remove the receiver batteries or unplug the receiver for a minute, then restore power. Our remote and receiver guide covers the battery and pairing steps.

Check the Wall Switch and Wiring

A wall switch can stay closed if its wires touch each other, get pinched, or melt near the firebox. Millivolt wall switches carry under 1 volt. Any on/off switch can work in that circuit, but heat-damaged switches are common.

Don’t open the wall switch or the valve compartment yourself. A technician can disconnect the switch wires from the valve and see what happens:

  • If the flame goes out when the switch wires are disconnected, the switch, wiring or receiver is at fault.
  • If the flame stays on, the valve is the problem.

Thermostat Mode and Smart Remotes

Some remotes have a thermostat or “smart” mode that cycles the flame on and off to hold a room temperature. From the outside, this can look like the fireplace turns itself on. Check the handset’s mode before you assume a fault.

A Stuck Valve

A gas valve can stick open because of debris or wear. This is a safety issue. Tapping on the valve or spraying lubricant on it doesn’t fix a valve, and it can hide a real problem. Replacing a valve usually costs about $150 to $400 for the part, plus labor, and must be done by a qualified technician. A leak test should follow any valve work.

When to Call a Technician

Call a qualified technician right away if:

  • The burner keeps running after you have closed the manual gas shutoff
  • You smell gas. Leave the home, don’t operate switches, and call the gas utility or 911 from outside.
  • The wall switch wiring is melted, scorched or loose

If the pilot won’t light or the burner won’t come on, see why a gas fireplace won’t ignite. If the smell is from the receiver or wiring, check gas fireplace smells.

The complete guide to gas fireplaces

How Gas Log Fireplaces Work: Logs, Inserts and Power Outages
Read the guide

Keep exploring

Guides from other topics

All topics →