Gas Fireplaces

How much does it cost to replace an igniter on a gas fireplace?

What does it cost to replace a gas fireplace igniter? Typical parts and professional prices, what drives the cost, and when a DIY swap makes sense.

On this page
  1. What a Simple Igniter Swap Costs
  2. Parts Prices
  3. Technician Visit and Labor
  4. Why Prices Vary
  5. DIY or Pro
  6. Before You Buy a Part

A simple professional igniter swap usually costs about $100 to $350 in total, depending on the part and your region. Parts alone often run $10 to $100. A control module or full pilot assembly costs more. These are rough ranges from several sources, so get a written quote before the work starts.

What a Simple Igniter Swap Costs

For a basic piezo or electronic igniter swap, expect a total in the range of $150 to $350 from a technician. Some estimates put the low end closer to $100. The total includes the service call or diagnostic fee, the part and the labor.

A replacement that needs a control module or a full pilot assembly is more involved. Installed, these often run $300 to $600 or more.

Parts Prices

Typical parts prices in the US:

  • Piezo push-button igniter: about $10 to $40
  • Thermocouple: about $10 to $30
  • Thermopile: about $20 to $60. Technicians often replace it at the same visit as the thermocouple.
  • Electronic spark electrode or igniter: about $25 to $100. Some OEM listings run higher.
  • IPI control module or ignition board: about $150 to $400
  • Complete pilot assembly: about $50 to $200

Prices vary by brand and part number, so check the price for your exact model.

Technician Visit and Labor

Most technicians charge a service call or diagnostic fee, often around $75 to $200. That fee can be part of the total if you have the work done the same day. A simple igniter swap is usually quick once the technician reaches the part.

An annual service, which typically runs about $100 to $250, can catch a failing igniter or thermopile before it stops working. That visit can be cheaper than a surprise repair in the middle of winter.

Why Prices Vary

  • Igniter type. A piezo push-button costs less than an electronic spark electrode, and a control module costs more than either.
  • Model compatibility. Igniters are rarely universal. The brand, model, serial number and fuel type (natural gas or propane) all matter.
  • Region and labor rates. Technician rates differ across the country.
  • Related parts. If the thermocouple or thermopile is also worn, the job costs more.

DIY or Pro

A piezo igniter can be a simple DIY job. It usually takes 15 to 30 minutes and often snaps or threads into a bracket with one wire to the electrode. Make sure the gas and power are off, and remove the batteries first.

A pilot assembly, thermocouple or valve involves gas connections. For those parts, a licensed technician is the safer choice. Any gas fitting you disturb should be leak-tested afterward with a soap solution or an electronic detector. Never test for leaks with a flame.

Before You Buy a Part

Check a few things before you spend money on a new igniter:

  • Batteries. A weak or dead battery can look like a failed igniter. Replace them with fresh alkaline cells first.
  • Gas supply. Make sure the shutoff valve is open and the tank, if you use propane, isn’t empty.
  • Pilot. A dirty or clogged pilot orifice can stop the flame even when the igniter works.

A clicking igniter with no flame often has another cause, such as gas flow or the thermocouple. Our guide to why a gas fireplace starter won’t ignite walks through the checks in order. For the broader ignition troubleshooting, see why a gas fireplace won’t ignite. An annual service is a good way to find worn parts before they fail.

The complete guide to gas fireplaces

How Gas Log Fireplaces Work: Logs, Inserts and Power Outages
Read the guide

Keep exploring

Guides from other topics

All topics →