A new gas fireplace has three parts that matter most: the venting, the gas line and the framing around the unit. In many places, only a licensed gas fitter can do the gas and venting work. Framing and finishing are the parts many homeowners can take on, if local rules and the manufacturer’s manual allow it.
Choose the Venting System First
Venting decides where the unit can go, so settle it before anything else. There are three common options:
- Direct vent. A sealed unit that takes combustion air from outdoors and exhausts through a pipe pair. The pipes are often coaxial, with one pipe inside the other. Direct vent can run out through an exterior wall or straight up through the roof, so it does not need a chimney.
- B-vent (natural vent). Uses room air and relies on a vertical run to carry exhaust up and out. It can only vent vertically.
- Vent-free. Has no vent to the outdoors, so combustion products and moisture stay in the room. Vent-free units are restricted or prohibited in some states, cities and provinces. Check local code before you consider one.
Use the venting system the manufacturer lists for your model. Mixing pipe brands or swapping parts can take the unit outside its listing.
Gas Line and Electrical Needs
The gas line is where most of the risk sits. Installers typically use black iron pipe or corrugated stainless steel tubing (CSST). The line must be sized for the unit’s total load and the length of the run, using the code tables. An undersized line can cause weak flames and fault the appliance.
A licensed gas fitter should also handle:
- A shutoff valve that is accessible, within 6 feet of the appliance and in the same room
- A sediment trap (drip leg) where the appliance instructions or code require one
- Bonding for CSST, usually with a copper jumper to the grounding electrode system. Follow the manufacturer’s instructions for this.
- Pressure testing, and leak testing of every joint
Most units with a blower or electronic ignition also need a 120-volt outlet or junction box. Plan for this before the walls go up.
Framing, Clearances and Finishing
Framing is the part many homeowners take on. Zero-clearance units are framed directly into a chase or enclosure. The clearances to combustible materials in the manual set how close the framing, mantel and facing can be.
- Follow the clearances in the manual, not general rules of thumb.
- Use the non-combustible surround materials the manufacturer specifies. Many builders use cement board instead of standard drywall near the unit.
- Leave the chases that the venting and wiring need before you close the walls.
- Check the mantel height and any TV placement against the manual.
Venting Through an Existing Chimney
If you are putting an insert into an existing fireplace, the vent usually runs up the chimney through a listed liner kit. There are two common kit styles:
- Coaxial: one pipe inside another
- Co-linear: two parallel flexible liners, one for intake air and one for exhaust, often 3 inches each
An unlined masonry chimney is not an acceptable vent for a direct-vent insert. Use only the venting system the manufacturer lists for that model. If the chimney has cracks, an offset or a failed liner, have it repaired and inspected before any insert goes in.
Permits, Inspections and Who Should Do the Work
Most jurisdictions require a permit and inspection for a new gas fireplace or insert. Many also require a licensed gas fitter for the gas line. Rules vary by state, county and city, so check with the local building department before you start.
A practical split looks like this:
- Often a homeowner’s job, if local rules allow: planning, framing and finishing, with the manufacturer’s clearances checked first
- Licensed professional: gas line, gas connection, leak testing and venting. Electrical hookups should follow local rules too.
Gas mistakes can be dangerous, and some are hard to spot without testing.
What Installation Costs
Costs vary a lot by region, unit type, venting and finishes. One installer’s guide puts an insert at roughly $1,000 to $3,000, with professional installation at roughly $500 to $2,500 on top. A full build with new framing, venting and a surround commonly costs more, often $3,000 to $10,000 or more. These are rough estimates. Get written quotes that list the venting kit, gas line work and permits separately.
Checks Before the First Fire
Before the first fire, confirm the following:
- The gas line passed a pressure test, and every joint was leak-tested with a soap solution or an electronic detector. Never check for leaks with a flame.
- The outdoor vent terminations are clear and the vent cap is in place.
- On direct-vent units, the glass and gasket seal properly.
- The work has passed inspection under the permit.
- A carbon monoxide alarm is installed near the fireplace and on every level of the home.
Some odor on the first few fires is normal burn-in. Our guide to gas fireplace smells explains which odors are normal and which need action. If you ever smell gas, leave the home, do not operate any switches, and call the gas utility or 911 from outside.
If you are still deciding between an insert and a log set, our explainer on how gas log fireplaces work compares the two. Once the unit is running, plan on an annual professional service, and read about carbon monoxide risk and detectors before you rely on the unit day to day.