Fireplace Parts and Mantels

How to Install a Floating Fireplace Mantel

Anchor a heavy-duty bracket or cleat into wall studs or masonry, then slide a hollow or pre-drilled mantel over it. Check clearances before you drill.

On this page
  1. Before you start: check clearances and the manual
  2. Tools and materials
  3. Step 1: Mark the height
  4. Step 2: Find studs or solid masonry
  5. Step 3: Mount the bracket or cleat level
  6. Step 4: Test-fit and bore the mantel
  7. Step 5: Slide the mantel on and lock it
  8. Check wiring, gas lines and the flue before you drill
  9. Common mistakes
  10. Safety

To install a floating fireplace mantel, anchor a heavy-duty bracket or cleat into wall studs or solid masonry. Then slide the hollow or pre-drilled mantel over it and lock it in place. Check the clearances first, because “floating” does not mean the code’s clearance rules stop applying.

Before you start: check clearances and the manual

Before you pick a height or drill a hole, confirm the clearances:

  • Minimum distance: combustible mantels must be at least 6 inches from a masonry opening.
  • Projection limit: within 12 inches of the opening, combustible material can project no more than 1/8 inch for every inch of distance.
  • Projections above the opening: a combustible projection more than 1-1/2 inches out generally needs to sit at least 12 inches above the top of the opening.
  • Manual first: the appliance manual and local code can be stricter, and the inspector has the final say.

For the full rules, see the mantel code guide.

Tools and materials

  • Stud finder or magnet
  • 4-foot level
  • Pencil and painter’s tape
  • Drill, with a hammer mode and masonry bits if you are mounting to brick or stone
  • Structural screws, 1/4 to 5/16 inch, or lag screws
  • Heavy-duty bracket, steel rods or a 2x4 cleat
  • Construction adhesive or set screws (optional)

Step 1: Mark the height

Decide where the top or center of the bracket will go, then mark a straight, level line across the wall with the level. Check the clearances at that height before you go further. If the mantel will project more than 1-1/2 inches above the opening, mark the line at least 12 inches above the top of the opening.

Step 2: Find studs or solid masonry

On drywall, find the wall studs. Studs are usually 16 inches on center, and a bracket should sit on at least two of them. Drywall anchors cannot hold a heavy beam. On brick or stone, find solid masonry for the anchors. The brick attachment guide covers anchor choice in detail.

Step 3: Mount the bracket or cleat level

For a wood-framed wall:

  1. Hold the bracket or 2x4 cleat along your level line. Make sure the holes line up with the studs.
  2. Pre-drill pilot holes to prevent splitting.
  3. Drive 1/4 to 5/16 inch structural or lag screws into the studs.
  4. Check the bracket with the level. Small errors show across a 60 to 72 inch beam.

For a masonry wall, use sleeve anchors or epoxy-set threaded rod. Tapcon screws are for light loads only. Drill with a hammer drill and a carbide masonry bit.

Step 4: Test-fit and bore the mantel

If the mantel is hollow or has pre-drilled rear holes, check the fit against the bracket or rods first. Bore the holes about 1/16 inch oversize, using a template that matches the rod spacing. A steel rod bracket usually has two or three rods of 1/2 to 5/8 inch, and each rod should be about two-thirds of the beam’s depth long. Rods that are too short cause sag.

Reclaimed beams are not always straight or square. Scribe the back of the beam or shim the bracket where the wall is uneven.

Step 5: Slide the mantel on and lock it

Align the holes in the mantel with the bracket or rods. Slide the mantel straight back until it sits flush against the wall. Tap it gently with a rubber mallet if needed. Then secure it with set screws, brad nails or finish screws, so it cannot be bumped off the bracket.

Construction adhesive in the bores is optional. It adds stability but does not replace the bracket.

Use two people to lift and seat a heavy beam. Support it with props until any adhesive has cured.

Check wiring, gas lines and the flue before you drill

Before you drill into any wall, check for:

Never drill into the firebox, smoke chamber or flue. If you are not sure what is behind the wall, stop and ask a professional.

Common mistakes

  • Using drywall anchors for a heavy beam. Drywall anchors cannot hold the weight.
  • Undersized rods. Rods that are too short cause sag over time.
  • Ignoring uneven masonry. Shim or scribe the mantel rather than forcing it.
  • Assuming “floating” means no clearance rule applies. It does not.

Safety

Use two people for heavy beams. Brick dust contains crystalline silica, so wear eye protection and a dust mask when you drill masonry. For the parts involved, see the parts of a fireplace. For sizing the beam before you install, see how big a mantel needs to be.

The complete guide to fireplace parts and mantels

Parts of a Fireplace: Hearth, Firebox, Mantel and More
Read the guide

Keep exploring

Guides from other topics

All topics →