Fireplace Makeovers

Brick Fireplace Makeover: Paint, Tile and Thin Brick Ideas

Brick fireplace makeover ideas covering paint, limewash, tile and thin brick, plus prep steps and safe ways to drill into brick for a TV or mantel.

On this page
  1. Start with clean, sound brick
  2. Paint, limewash and whitewash
  3. German schmear and skim coats
  4. Keep high-heat paint inside the firebox
  5. Tile over brick
  6. Thin brick veneer
  7. Drilling into brick for a TV, mantel or art
  8. Clearances for wood trim and mantels
  9. Safety
  10. Common mistakes

A brick fireplace can look dated, but it’s one of the more workable surfaces to update. The right approach depends on the condition of the brick and whether it’s already painted. Painting is the cheapest update, and it’s hard to undo. Painted brick is effectively permanent, so decide before you pick up a roller.

Start with clean, sound brick

Scrub the brick with a stiff brush and TSP or a TSP substitute. This removes soot, grease and efflorescence, the white salt deposits that show up on old masonry. Let it dry for 24 to 48 hours before you finish it.

Look for cracked or loose brick and crumbling mortar, and repair those first. To check how the brick absorbs, sprinkle a little water on it. If the water soaks in quickly, the brick suits limewash or a veneer bond. If it beads up, it’s probably sealed or painted.

Paint, limewash and whitewash

For a solid color, start with a masonry primer, then use an acrylic masonry paint or a breathable mineral-silicate paint. A 3/4- to 1-inch nap roller covers the face, and a brush works the mortar joints.

Limewash soaks into clean, unpainted, unsealed brick and can be partly wiped back while it’s still wet. It won’t bond well to painted or sealed brick, so check the surface first. Whitewash is a thinner wash, usually latex paint diluted with water, often in roughly equal parts. Adjust the ratio for the opacity you want and test a small patch before you commit.

Matte white and black are common choices for a modern look. Bolder colors such as green or navy also work, so test a sample board or a hidden patch before you paint the whole face.

German schmear and skim coats

A German schmear smears wet mortar over the brick and wipes part of it away, so the mortar fills the joints and leaves a rustic, textured face. It’s a skilled job, and the result is permanent.

A skim coat of lime plaster, microcement or mortar gives a smooth, modern surface. The brick needs to be clean, and it needs a bonding primer or base coat first.

Keep high-heat paint inside the firebox

Leave the firebox bare or use a high-heat paint rated around 1,200°F. Regular latex paint isn’t suitable inside the firebox, even if the outside of the brick is painted with it. This is one of the most common mistakes in brick makeovers.

Tile over brick

There are two common ways to tile a brick fireplace:

  • Skim coat: Clean, unpainted brick, flattened with a polymer-modified thinset or mortar skim coat, then tiled.
  • Cement board: 1/2-inch cement board fastened to the brick with masonry screws, then tiled.

Tile doesn’t stick well to sooty or painted brick, so clean and prepare the surface first. Porcelain and ceramic tile are noncombustible finishes, which makes them a good choice near the opening. Wood trim and mantels still need clearance (see below).

Thin brick veneer

Thin brick is about 1/2 to 1 inch thick. It’s set with polymer-modified thinset or Type S mortar, with joints about 3/8 to 1/2 inch wide filled with a grout bag. This gives you the look of new brick without tearing out the old. Keep in mind that the extra thickness changes how a mantel or TV sits, so plan for it before you start.

If you want a stone look instead of brick, see stone fireplace surrounds.

Drilling into brick for a TV, mantel or art

Use a hammer drill with a carbide masonry bit. A standard drill struggles with brick and dulls quickly. Start slowly so the bit doesn’t skate across the face, then add the hammer action. Wrap painter’s tape around the bit to mark the depth, and clear the dust before you insert the anchor.

Where to drill:

  • Mortar joints are easier to drill and fine for light items such as small frames. Mortar is softer, though, and can crumble.
  • Solid brick holds heavier loads. For a TV mount or a mantel, drill into the brick face and avoid the edges, since they can split.

Anchors:

  • For Tapcons, a 3/16-inch screw uses a 5/32-inch bit, and a 1/4-inch screw uses a 3/16-inch bit. Check the package for the embedment depth and drill a little deeper than that.
  • For heavy loads, use sleeve anchors or lag shields in solid brick. Wedge anchors can crack brick.
  • Old or cored brick holds less. Test-load the anchor before you trust it with a TV.

For TV height and mounting, see how high a TV should hang above a fireplace. For hanging art and mirrors on brick, see what to put above a fireplace.

Clearances for wood trim and mantels

Brick doesn’t change the clearance rules for wood. As a rule of thumb for a masonry fireplace, keep wood trim and other combustibles at least 6 inches from the opening. Within 12 inches, trim can project no more than 1/8 inch for every inch of distance from the opening. Keep wood framing away from the chimney masonry, too.

Safety

  • Wear an N95 or better respirator, and eye protection, when cutting, drilling or grinding brick. Brick and mortar dust contain silica.
  • Locate the flue and any chase before drilling. Never drill into the firebox, smoke chamber or flue.
  • Painted surfaces in homes built before 1978 may contain lead. Test before you sand.

Common mistakes

  • Using regular latex paint inside the firebox
  • Applying limewash over painted or sealed brick
  • Setting tile on sooty or painted brick without prep
  • Drilling into mortar joints for a heavy TV mount

The complete guide to fireplace makeovers

Fireplace Makeover Ideas: Modern Designs on Any Budget
Read the guide

Keep exploring

Guides from other topics

All topics →