Yes, but the answer depends on what kind of fireplace you mean. An electric or decorative fireplace is a realistic DIY project. A working wood-burning or gas fireplace is a construction job. In most US jurisdictions it needs a permit, inspections and code-compliant parts, so it’s a job for a licensed trade or a pro.
The options, from easiest to hardest
- Electric or decorative: Plug-in electric units are the simplest. Most run on 120 V and produce about 1,500 W of heat. A framed surround or media wall around one is a practical DIY project.
- Ethanol: No vent is needed, but ethanol units give off little heat. Refill only when the unit is cold and out.
- Factory-built (zero-clearance): These units are listed (UL 127) and installed to the manufacturer’s instructions. Use only the chimney and parts the manufacturer lists for that unit.
- Modular masonry kit: Kits built on a set design, such as pumice systems, still need code compliance and an inspection.
- Site-built masonry: The most involved option. It needs a footing, firebrick, a flue and a hearth, all built to code.
Electric and decorative builds
Most DIY builds are a framed surround or media wall around an electric insert. The usual steps are:
- Plan the layout. Map the fireplace, mantel and TV with painter’s tape, then check the studs and any existing outlets.
- Frame the wall. Use 2x4s and 2x8s, sized for the insert and any stone or tile. Secure the frame to the studs and level it.
- Install the insert. Set the unit in the framed opening and fasten it as the manufacturer directs.
- Finish the surround. Cover the frame with drywall, plywood, shiplap or cement board. Add the mantel and trim, then tape, sand, prime and paint.
If you need a new outlet, bring in a licensed electrician.
Never burn a fire in a decorative or faux fireplace that wasn’t built for one. Install CO and smoke alarms near any fuel-burning fireplace.
Real wood-burning or gas fireplaces: what code covers
Building a working fireplace is governed by local building codes. These are the typical requirements in US model codes, which vary by place and edition. Confirm them with your local building department before you start.
- Permits and inspections: Most jurisdictions require a permit and inspection for a new wood-burning or gas fireplace.
- Footing: A concrete footing at least 12 inches thick, extending 6 inches beyond the fireplace on each side.
- Firebox: At least 20 inches deep (Rumford designs can be shallower, at a minimum of 12 inches). The firebox is lined with firebrick at least 2 inches thick, set in medium-duty refractory mortar, with joints no wider than 1/4 inch.
- Hearth: At least 4 inches thick. The noncombustible hearth extension is at least 2 inches thick and extends 16 inches in front and 8 inches to each side for openings under 6 square feet. Larger openings need 20 inches in front and 12 inches to the sides.
- Flue: The flue size comes from the code’s tables for your opening. Don’t size it by rule of thumb.
- Chimney height: Often described as the 3-2-10 rule. The chimney top sits at least 3 feet above where it exits the roof, and at least 2 feet above anything within 10 feet.
- Clearances: A masonry chimney needs 2 inches of clearance from combustible framing inside the building, and 1 inch on exterior walls.
- Factory-built parts: Use only the listed chimney and parts from the same manufacturer. Parts from different brands can’t be mixed.
- Gas: Gas line work often needs a licensed gas fitter, and rules vary by jurisdiction.
Common misconceptions
- “Ordinary brick and mortar will line a firebox.” It won’t. Use firebrick and refractory mortar.
- “Any metal pipe can serve as a chimney.” It can’t. Use a listed chimney system.
- “Parts from different brands are interchangeable.” They’re not. Use the listed parts for your unit.
- “Ventless means no effect on indoor air.” Ventless units still release combustion products into the room, and some places restrict them.
When to hire a pro
Hire a licensed mason, gas fitter or electrician for any masonry, gas line or new electrical circuit. A pro with fireplace experience is the right choice for a new chimney, since flue sizing and clearances are easy to get wrong. Electric and decorative builds are the realistic DIY route.
For the wall around an electric or decorative unit, see DIY fireplace surround plans. For the broader range of options, see fireplace makeover ideas.